Company News

How to solve the problem of laser cutting failure?

The laser cutting machine can produce exquisite objects through its own energy. But long-term use of the cutting machine will cause failures. Through the video, we can see that the cutting machine failed to cut the material during the operation.Next, we solve the problem in turn.   1、Adjust software parameters 1. Adjust the control panel 2. Adjust RDWorks cutting software We can adjust the parameters of the machine through the control panel and RDWorks cutting software . 2、Check lens At the same time, Stain on the reflective [...]

08/06/2020 By Company News, FAQ, News, Service Read more...

How to replace the laser tube and power supply

In the process of using laser cutting machine, it will encounter many problems. As the main parts of the machine, the laser tube and power supply require frequent maintenance and cleaning. Next, we will explain the replacement of the laser tube and power supply.   Watch the video   Before replacing the laser tube and power supply, you need to cut off the power of the machine.In order to avoid the phenomenon of high-voltage ignition, remember to install an insulating sleeve on the [...]

07/21/2020 By Company News, FAQ, News, Service , , , Read more...

How to adjust the optical path of laser cutting machine

Laser cutting machine cutting process:  The high-pressure discharge excites high-concentration CO2 gas to generate laser ligh, through laser reflective mirror and the laser focus lens, the laser beam is concentrated in a small area. The high concentration of energy enables rapid local heating to melt the working area . In this process, the optical path taken by the laser is a fixed path controlled by the lens. However, when the machine has been working for a long time, the light [...]

07/13/2020 By Company News, News Read more...

Live Notice，Let’s meet online

OMG Mactron open on live again! This time, we bring some laser machines Fast speed, good quality and high efficiency Are the best cost-effective products! If you have any questions about laser equipment Ask questions or join the interaction. Alibaba Live June 25th We continue to meet you in the Alibaba To explore the brilliance and charm of laser equipment together Scan the QR code below to watch the live broadcast on time Made in China live broadcast Expo：Manufacturing & Processing Machinery Date：Jun 15, 2020 to Jun 24, 2020 (00:00 – 23:59) Scan the [...]

06/19/2020 By Company News, Exhibition Information, News , , Read more...

【MACTRON CLASSROOM】How To Correct Parameters Of Cutting Machine?

In the process of cutting, workpiece surface is heated to vaporization temperature quickly by focused laser beams, forming High pressure steam and spraying outward at supersonic speeds. When high-pressure vapors spray outward, the melted materials are blown away in the kerf till the workpiece is finally cut. The laser cutting machine equipped with CCD vision positioning system is not only suitable for various materials and objects, but also can realize automatic positioning and precise cutting operation.   The parameters is a [...]

05/22/2020 By Company News, FAQ, News, Service , , Read more...

How to adjust the focal length of the cutting machine?

As a new generation of large-scale intelligent mechanical equipment, laser cutting machine has the advantages of high processing accuracy, good cutting effect and wide application. It can not only engraving on the material, but also cut the whole board of large-format materials. The method of adjusting the focal length of the marking machine and the cutting machine is slightly different. In this issue, we will teach you two ways to adjust the correct focal length, remember it!   Watch the video   If [...]

05/22/2020 By Company News, News , Read more...

【MACTRON CLASSROOM】Software Project Teaching

The software is indispensable instructions for laser equipment. In the process of daily use of equipment, we may encounter software failures, which need to be checked and solved in turn. Below, we introduce some common software problems, please watch carefully, grasp the solution.   The Software is damaged Before using the operating software, you need to back up your files. If the software is damaged and cannot be used, it needs to be reinstalled.   The software is encrypted If the software is encrypted, you need [...]

03/21/2020 By Company News, News , , Read more...

Mactron carried out multiple disinfection to control of the epidemic

In the face of the still serious epidemic and changing data, Mactron has always maintained the principle of “prevention and control of the epidemic, safety first”. In order to make customers rest assured to buy and use products, The staff carried out multiple disinfection on the product body and packaging before delivery , to ensure that customers receive safe products, effectively protect the rights and interests of consumers. ●Product disinfection: wipe and sterilize with 95% medical alcohol ●Package disinfection: disinfect with [...]

02/29/2020 By Company News, News Read more...